RASPBERRY PI 4 MODEL B — VENTED ENCLOSURE WITH PORT ACCESS This is a roomy practice prototype for a bare Raspberry Pi 4 Model B. It is not a tested commercial case, a Pi 5 case, or a guarantee of fit with HATs, heatsinks, fans or every cable housing. No physical fit or thermal test has been performed. SOURCE AND WHAT THE DRAWING ESTABLISHES Official mechanical drawing: https://pip.raspberrypi.com/documents/RP-008343-DS Official board information: https://www.raspberrypi.com/documentation/computers/sbcs.html#raspberry-pi-4-model-b raspberry-pi-4b-full-page.png is the entire official PDF page rasterized at 1800 x 1273 pixels, with all margins retained. The earlier optional cropped PNG is also included. The original drawing belongs to Raspberry Pi; it is not Homebrew's drawing and is not covered by a Homebrew CC0 claim. Source attribution is retained. The mechanical drawing, not the electrical circuit schematic, supplies board dimensions and hole locations. The PCB is 85 x 56 mm. Its four mounting centers are (3.5, 3.5), (3.5, 52.5), (61.5, 3.5), (61.5, 52.5) mm from the board's front-left corner in the drawing's top view. The pattern is 58 x 49 mm. Do not use four equal corner insets: the board extends farther past the right-hand pair of holes. The 20 mm height envelope, case sizes, 5 mm lift, 2 mm screw pilots and all opening sizes below are reviewed design choices. They are not exact connector dimensions extracted from the drawing. The service windows deliberately group ports and allow room for plug bodies. Measure your actual board and cables before using this as a finished enclosure. Add hardware and cooling clearances as needed. 1. READ THE DRAWING Open Model Studio > Enclosure. Upload raspberry-pi-4b-full-page.png into the component's Spec-sheet image field and select Read spec sheet. Wait for the local reader. Compare its suggestions with the drawing. Missing or uncertain dimensions must be entered manually; do not treat a Z component-height label as a port-center height. Do not accept a guessed four-corner mounting pattern. The improved reader was rerun through the normal upload screen with the complete, uncropped mechanical drawing. No manual cropping is required for this example. It returned the 85 x 56 mm board, all four mounting centers, and seven visible edge-connector center positions: front X=11.2, 26, 39.5, 54 mm; right Y=9, 27, 45.75 mm. Coordinates are traced through printed dimension chains and checked against circular holes or edge-crossing housings. Connector types remain unconfirmed. Opening widths/heights, port-center Z, complete board height and hole/pilot diameters are not established by this drawing reader; fill them only after review/measurement. Z= annotations alone are component extents, not port-center heights. The full-page run recovered all four mounting centers and all seven visible edge-port positions. The reader preserves page orientation, recovers dimension labels missed beside arrows, and checks the original dimension lines. Review all suggestions and the whole drawing. 2. REVIEW THE BOARD AND POSTS Use one component named Raspberry Pi 4 Model B. Set Width 85, Depth 56, Full height 20 mm. Expand Position & mounting holes: X=3, Y=3, Bottom lift Z=5 mm. Choose Use known dimensions, then Add mounting point to review for each of the four detected holes. Check the board-local X/Y centers against the values above; the reader must not substitute a four-equal-inset pattern. Set each Screw pilot diameter to 2 mm. These are printed pilot holes; verify/drill them for your chosen mounting screws. They are not the PCB's mounting-hole diameter. 3. CASE SETTINGS Choose Breathable — vented lid. Wall thickness 2, Floor thickness 2, Lid thickness 2, Lid fit clearance 0.25 and Component spacing 3 mm. Choose Keep my positions; enter Interior width 91, Interior depth 62, Interior height 35 mm. Do not use Arrange & fit, which would replace these dimensions. The body outside is 95 x 66 x 37 mm. The lid is printed separately, underside up, and flipped for assembly. Combined print layout: 198 x 66 x 37 mm. Download the individual parts if that layout is too wide for your bed. 4. PORTS AND WIRE ACCESS The seven Add port opening to review buttons copy the detected wall and center plus the component X/Y offset. Missing width, height and vertical center remain blank. To reproduce this grouped-window prototype, remove individual suggestions and use the six intentional service/cable windows below instead of adding both sets. Enable Allow wire entry / cable-gland holes. Add these six rectangular openings: Name / Purpose / Wall / Width / Height / Across U / Up-or-depth V (all mm) USB-C, two micro-HDMI, AV / Port access / Front / 64 / 18 / 37 / 13 USB stacks and Ethernet / Port access / Right / 54 / 22 / 32 / 16 microSD card access / Port access / Left / 28 / 8 / 30 / 6 GPIO cable access / Wire entry / Lid / 62 / 8 / 35.5 / 55.5 Display ribbon cable / Wire entry / Lid / 8 / 24 / 6 / 33 Camera ribbon cable / Wire entry / Lid / 8 / 24 / 49 / 15.5 Orientation follows the drawing as shown: front is the lower edge carrying USB-C/HDMI/audio; USB and Ethernet are on the right. X is the 85 mm direction, Y the 56 mm direction. Port coordinates use the CASE INTERIOR, not board-local coordinates: U=X on front/back, U=Y on left/right, V=height above the inside floor. On the lid, U=X and V=Y in the assembled case. The generator mirrors lid Y for its underside-up print layout automatically; do not mirror the entered values yourself. The lid's remaining vent slots are added by Breathable automatically. Large access windows are intentional; they are not close-fitting individual connector cutouts. Verify that actual plugs can reach their sockets and that the microSD card can be inserted and removed. GPIO and ribbon openings allow cables through; they are not HAT mounting features. 5. PREVIEW AND GENERATE Select Update 3D enclosure preview. Inspect Exploded, Assembled and Hide lid. Confirm all four posts, the service windows and the lid openings/vents. The board box is a layout guide and is excluded from the print. Tick the review checkbox, then Generate enclosure STL. Wait for the normal queue and reopen the saved result. 6. DOWNLOAD AND PRINT Download printable STL contains both parts side by side. Download body & lid ZIP provides individual STLs; print the layout OR the individual parts. Print body floor-down and lid flat, then turn the lid over for assembly. Select your own printer/filament and inspect every layer, posts, bridges above service windows, screw pilots, vent slots and lid clearance. Supports or altered orientation may be needed for your printer/material. Make a fit prototype before installing electronics. Use appropriate fasteners and verify cable access, retention, cooling and board isolation yourself. The sample kit's actual output, saved settings and extraction report let you compare your result. Settings JSON is a reference, not an importable website project. Native slicing and closed-mesh checks do not replace physical fit, electrical or thermal testing. Instructions: https://homebrewprinting.com/forum/topic/ai-enclosure-instructions#studio-samples