TWISTED CURVED LOOP - RECREATE AND EDIT CONVERT THE ORIGINAL MESH 1. Open https://homebrewprinting.com/ai-stl-studio and choose Mesh to CAD. 2. Upload input.stl and choose Millimeters. Keep Merge flat faces and Recognize round surfaces ON. 3. Set Fit freeform surfaces to ON. Leave optional simplification OFF. 4. Keep sewing tolerance 0.01 mm and maximum surface deviation 0.05 mm. 5. Convert to editable CAD, wait for the queued job, and inspect the report. Download STEP or FreeCAD. EXPECTED RESULT 3,456 input triangles became 3,456 editable B-spline faces; the central opening was preserved. No simplification. Recognize round surfaces and Fit freeform surfaces ON. The edited example adds a 2.5 mm hole through the loop at X=18, Y=0. Maximum fitted deviation 0.0495 mm. Pocket Refine is disabled in the edited FreeCAD file. The source has 3,456 triangles; the input mesh was not simplified before CAD reconstruction. Exporting fitted CAD surfaces back to STL creates a new tessellation, so that STL can have a different triangle count. CAD surface fitting is bounded approximation, not recovery of original design history. The server test used FreeCAD 1.0.2. Timings vary with server load; detailed curves can take several minutes. TRY THE READY-MADE PARAMETRIC EDIT 1. Open edited.FCStd in FreeCAD and expand Body. It contains ImportedSTEP, EditableHoleSketch and EditablePocket. 2. Double-click EditableHoleSketch, change its diameter constraint (currently 2.5 mm), close the sketch, and recompute. Keep the diameter close to the tested value so it stays within the surrounding material. 3. Select EditablePocket to change its Length. The tested length is 16 mm. On dense spline parts set Data > Refine = false if recompute is slow. 4. Save under a new filename. Select the final solid/Pocket and export STEP for CAD exchange or STL for slicing. edited.step is the saved solid geometry and does not retain the sketch history. CREATE THE SAME EDIT FROM THE CONVERTED FILE Open model.FCStd and activate its existing Solid body. Create a sketch on the XY base plane. Set its Placement Position Z to 8 mm and draw/constrain a circle centered at X=18, Y=0 mm, initially 1.5 mm diameter. Make a dimensioned Pocket 16 mm long in the negative Z direction. For the curved parts, use this base-plane sketch because there may be no suitable planar face. Change the sketch diameter to 2.5 mm and recompute. The tests saved/reopened the edited solid, then changed diameter and depth again. If starting from model.step instead, import it as a solid and create a Part Design body containing that solid before adding the sketch. REFINE TIP Select a Pocket in the model tree, choose the Data tab, and set Refine to false if large spline models recompute slowly. Refine cleans up residual edges after the cut; disabling it does not decimate your mesh or turn spline faces into flat facets. The curved examples ship with this setting already disabled in edited.FCStd and edited-native.FCStd. Inspect the recomputed solid before exporting. FILES input.stl is the original upload; converted.stl tessellates the checked CAD output. Do not load both on top of each other when printing. model.step and model.FCStd are the unedited conversion. edited.FCStd contains the STEP-imported body and an editable sketch/Pocket. edited-native.FCStd shows the initial Pocket diameter added directly to the native conversion; edited.FCStd contains the later enlarged diameter. model.scad contains a tessellated polyhedron, not recovered parametric CAD. Checksums verify every companion file. settings-reference.json is a manual-entry reference, not an importable project. verification.json records the actual software tests; conversion.json is the original conversion report. These are geometry/software examples, not physically printed or load-rated parts. Spline seams need inspection; tangent continuity is not guaranteed. SolidWorks was not directly tested.